Payment & Shipping Terms:
|Compression:||H.264||Host Weight:||1.95 Kg|
|Host Dimension:||200(L) X187(W) X62(H) Mm||TV System:||PAL / NTSC|
|Display Quality:||TV: D1 VGA: High Definition||Voltage:||DC 8 ~ 36V|
|Warranty:||14 Months||Resolution:||4ch 720P(1280x720)|
dvr digital video recorder,
vehicle digital video recorder
|Video Compression||H.264 Compression|
|OSD||Overlays information such as date time and vehicle ID|
|GUI||Graphical User Interface||Setup system parameters with the remote control.|
|Video Record System||Video Input||4CH 720P AHD input,aviation connector, 1.0Vp-p, 75Ω|
|Video Onput||1 CVBS, 1.0Vp-p, 75Ω,Aviation,Support 1CH Full Screen,4CH Screen view|
|Preview||Support 1 channel and 4 channels preview.,Support Manual/Alarm Trigger full screen preview|
|Resolution||720P/D1/HD1/CIF, MAX:4 channels of 720P and 4 channels of D1|
|Image Quality||1-4 levels, 1 is the highest level.|
PAL: 100f/s , CCIR625 line,50field;
|Record Mode||The default setting is auto recording after power on. Timed recording, alarm trigger recording and manual recording are supported.|
|Audio||Audio Input||4CH Aviation Plug Input|
|Audio Output||2CH,headphone connect at front panel, BNC Connect on Back panel|
|Compression||G.726 compression, 8KB/s speed|
|Alarm Input||7CH Alarm Input,1CH AD Input,impulse speed input,Alarm Linkage|
|Alarm Output||2CH Alarm Output,Support Light/Sound alarm sensor,Oil/Power cut off|
3CH RS232, POS/Fuel Sensor/LED Advertisement Connection
|1CH 485 Interface,Connect PTZ Camera|
Support Built in 3G transmission,, WCDMA, CDMA2000,GPRS, EDGE；
|GPS Position||Support Built GPS/BD Module|
|HDD||Max 2.5” 2TB HDD|
|Storage||SD Card||Max 128GB SD Card Mirror Recording Keep Data Safety|
|Update||Support USB Updating, SD Card Updating,OTA Remote Updating|
|File System||Special FAT32 File System|
|USB||USB Interface on Front Panel for data back up by U Disk,Hard Disk|
|Record Replay||Video Search||Search By Record Time/Record Type etc|
|Playback||Max support 4CH Replay /Stop/Fast/Slow at same time|
|Support forward and backward play at the speed of: x 2,x4,x8,x16.|
|Security||User/Admin 2 Level Different Password|
|Optional Functions||Voice Call||Support voice call each other|
|TTS Voice Broadcast||Support TTS voice broadcast function.|
|Serial Expand||Support LED Advertisement Panel,Oil Sensor,POS,Bus Station Broadcaster,Car OBD,ect.external device|
Q:When Device issue appear,you are confused on how to solve it.
A:Check Device Item No & Firmware Version,sent back to us with detail description of issue.Our Technical Team will handle it.
More detail you described,easier for us to solve it quickly.
Q:Video Output Lost
A:1.Check situation of DVR:Device Input Power;Power Cable Connection;GND Connect to battery;fuse;RED & Yellow Cable of Power must connect together;
2.Check the Screen Power or Check if the Screen change to related AV Channel;
3.Check the connection of Video Output & Screen Cable;
Q:Device keep Rebooting
A:1)Check working power,if low power device will keep rebooting;
2) HDD/SD Card error, remove storage device and turn on device checking;
Q: If the video input interface of the device and camera is different.
A:The DVR is using 4PIN type port, the camera is BNC port or Aviation, if it is different, please use the X-over to connect, or connect according to the DVR Line sequence definition
Q:Device on with HDD but not recording;
A:1)Check SD/HDD if format;if not please enter Main GUI--System Set--Format,format HDD/SD Card;
2)If close Recording ,or set Timed Recording mode, if yes it won’t recording if not the time set
3)If the HDD is connect well, if the HDD/SD light is on.
Q: Video files lost, or there is no video files at a certain period time.
A: 1. Analysis the lost video and ensure the lost time period.
2. Confirm if the DVR was opened at that time, such as crashed midway park, loading and unloading ect. And the device didn’t set the delay recording
Q: Can not control the Car PTZ, can not rotate to all direction.
A: If the agreement and Baud rate of the PTZ is setting right,if the address code is corresponding, if the video channel is setting to max when control the PTZ. Like if is control the first channel, then must set the first channel image to be max.
Q: With GPS but no GPS coordinate Information
A:1)Check if GPS module exist;
2)Check GPS Antenna connection,suggest install on the outside place with strong signal;
3)If testing in office, suggest put GPS Antenna out of window;
4)If working environment not good will related to no GPS Information or wrong information;
Q:Deviation of GPS Location on Map?
A:The signal is effective if the GPS module has been positioning, there are so many reasons caused bias, government restriction, permissible error, GPS signal break off, The actual satellite map error occurred for the security, GPS Correction can solve the problem.
Q:If using 3G ,what should we concern?
A:1)Choose inside wireless module WCDMA,EVDO,TD-SCDMA, relative module setting is different then SIM Card is different, please make sure the module is corresponding with the SIM Card.
2)If Server IP & Port set correct,if 3G signal strong for dialing;3G dialing successfully or not;
3)Check 3G Antenna connection,dialing will be failed if 3G signal too weak;
4)Check SIM Card 3G Flow
Q:When meet device offline or no video,what should be done first?
A:1)Press INFO key to enter the system Info page,check if SIM Card exist,3G signal and dialing status,Antenna connection,Check SIM Card 3G Flow,change to a new SIM Card check again;
2)3G Signal strong but dialing fail,check if center IP & Port set correct;
3)Check if Device ID already be occupied;
Q:3G Signal is intermittent, video get stuck ?
A:At present, signal coverage of the WCDMA and EVDO is very wide, but still there are some mountain area signal is weak, this will influence. Then check if the frame rate in Sub-stream setting is too high.
Q:WIFI Signal 60/100,connect failure;
A:General condition, connection is no problem when the signal intensity up to 60/100 if WIFI setup are right. If the device can not be found in LAN, then you should check if setting SSID and password, IP Address, besides, check the Encryption Type and authentication mode if setting according to requirements.
Q:Device working but can not see Vehicle and video on client software
A: 1)Check if Center Server running and device Number if using;
2)Check Server IP and Port parameter setting;
3)Check is using 3G or WIFI for connecting, if 3G check the 3G Model WCDMA or EVDO and related SIM card,3G antenna connect normally/APN setting/Center No. setting;
If it still can not work,please offer the most detailed information to us for technical support
Q:Device Online but can not see video
A:1)Please set Low Sub-stream,when sub-stream set high it will effect the transmission because of the network;
2)Network environment not good;
Q: Device works well in the Client, but cannot see the video a period time later.
A:1.Check if connect to server successfully on device, if dialing probably SIM Card no 3G Flow,change another SIM card for testing;
2.Check if Device Number be changed,if yes,need add device to server again;
3.If still can not view video after previous 2 steps,please check if 3G module error;
Q: Video Lost in certain channel?
A: Possible reasons are as follows
1. This channel has no video input
2.The camera of this channel breaks down or work abnormality
3.If the camera takes an electricity power from the equipment directly, may be the
equipment’s electric voltage isn't enough to make camera work as usual;
d) The cable that links this channel has problem
Q: Can’t playback files on PC successfully?
A: Possible reason is as follows:
1.Have never chosen a record file or document path; please choose the path that records file first before playback.
Q: Remote control not works?
A: Probably of the reasons are as follows:
1.The remote control didn't pack battery;
2.2.The remote control damages;
Q: During playback, the map doesn't show?
A: Possible reasons are as follows: Net cable did not connect to PC; Net works, but the computer can not get to the Internet;
Q: When SD card and HDD records, How is the record coverage?
A: SD card and HDD will record circularly for each other. When they are full, they will delete the original video records respectively.
1—HDD Lock, it’s used for unload hard disk. Device will power off automatically if power on when HDD lock is open;
2—HDD Fixed Screw . Please manually tighten screw after installing hard disk drive, to prevent HDD slip out ;
3— Status Indicator LED,Details as below :
PWR — Power Indicator LED. LED light means system has powered on.
GPS — GPS/BD Status indicator light. LED ON—Positioning success,
LED FLASH—In positioning ,LED OFF—No GPS Module.
HOT —Hard disk heating LED. LED ON—HDD is heating,
LED OFF—HDD doesn’t open heating.
SD — SD card Indicator LED. LED ON—Card is recording,LED FLASH—Card exists but not recording,LED OFF—Card does not exist.
HDD — HDD card Indicator LED.LED ON—HDD is recording,LED FLASH—HDD exists but not recording,LED OFF—HDD does not exist.
REC — Video Recording Indicator LED.LED ON—In the recording；
ALM — Alarm Indicator LED. LED ON — In the alarm ；
NET — Network Indicator LED. It changes based on dial-up connection status, details as below:
LED OFF—No communication module,
LED INTERMITTENT FLASH—SIM CARD does not exist ,
LED QUICK FLASH (1:1) —Device is dialing,
LED SLOW FLASH (3:1)—server connection is not successful,
LED ON - server connection is successful.
4—SIM Card and SD Card Slot; ( When installation gap towards inside, metal touch spot face down )
5—Front audio and video output interface
Contact Person: Abby Cai